Teamcenter Visualization Mockup – Clearance Analysis

Teamcenter Visualization Mockup – Clearance Analysis

Many years ago, or so it seems, one of the methods for checking clearance and interference’s was performed through the use of drawings. By cutting sections through the parts in an assembly drawing, the detail of that assembly could be shown in a section view, and then distances could be measured between parts to determine whether clearance objectives where being met. This task involved tools such as a compass, a drafting pencil, and a scale along with the ability to draft accurately. Another method was to build a full size scale mockup, or buck, of the part or assembly to visually check for interference’s and you could also use a wide variety of tools to take measurements.

While there may be nostalgia for these methods, modern CAD tools and technology can accomplish the same tasks in far less time. By assembling parts and cutting sections through the CAD data, we can then electronically measure for clearance between parts and assemblies. This process is much faster than with drawings, and can greatly improve productivity. However, what if you had to find clearance issues within a very large data set like an engine, or transmission, or an instrument panel? This amount of data loaded into a CAD session can be difficult to work with due to the model size and complexity of the parts within these assemblies. Also, the tasks of cutting sections and taking measurements required for the clearance analysis is a skill only possessed by the proficient few.

Because of this and other problems, solutions were created that transform CAD data into lightweight tessellated data files. By translating the data into a JT (Jupiter Tessellation), or similar file, the viewer can read very large assemblies quickly and perform a multitude of tasks on that data.

One such viewer is Siemens Teamcenter Visualization Mockup, better known as VisMock. This tool is more than just a viewer, it’s a real-time digital mockup tool that you can use to detect and solve design issues early in your product lifecycle, getting you from art to part faster and cheaper than ever before! And, VisMock is a very intuitive and easy software to learn and use. With VisMock, the learning curve is minimal in comparison to learning a CAD system, so this lends itself well to those non-expert users who are looking for quick answers to design issues. For example, a non-CAD user can go into VisMock and perform a Clearance Analysis, and in a matter of minutes have the answer to a nagging question on whether there is a clash or clearance in their assembly, or to adjacent parts and assemblies.

VisMock is used in Automotive, Aeronautic and Aerospace, Ship Building, and Consumer Product industries as a design verification tool that can reduce or eliminate the use of rapid or traditional prototypes. This can further reduce the cost of bringing a product to market.

Teamcenter Visualization is available in four different levels: Base, Standard, Professional, and Mockup. Each level builds upon the one before it. Siemens offers Teamcenter Visualization this way so that it is scalable, so as your company grows, so can your visualization software.

Some of the key benefits for using Teamcenter Visualization Mockup:

  1. User friendly application that gives quick results for aiding in critical decisions across all disciplines within your company as well as your entire enterprise.
  2. Reduce cost by reducing the need for traditional and rapid prototypes.
  3. Making use of your digital twin moves critical decisions earlier in the product lifecycle where making changes to CAD data is easier and cheaper than correcting mistakes to a physical product.
  4. Four different levels to fit your current needs and for scalability.

So, can your business benefit from faster decision making by a wider range of participants? Teamcenter Visualization can facilitate this requirement and bring substantial benefits.

For more information contact Tata Technologies at
info.americas@tatatechnologies.com or visit our website at www.tatatechnologies.com

Tata Technologies is a Siemens Platinum Smart Expert Partner indicating our validated expertise in NX-CAD.

Tony Alfonsi

Siemens Application Engineer at Tata Technologies Inc.
Tony has worked as a Tool Designer and Product Designer for the Automotive, Aeronautic, and Consumer Industries. Over the years he has taught CAD and PLM to many cross functional teams, and is currently working for Tata Technologies Business Development Team as a Siemens Application Engineer.
Tony Alfonsi

Leave a Reply

Your email address will not be published. Required fields are marked *

© Tata Technologies 2009-2015. All rights reserved.

Tony Alfonsi

Siemens Application Engineer at Tata Technologies Inc.
Tony has worked as a Tool Designer and Product Designer for the Automotive, Aeronautic, and Consumer Industries. Over the years he has taught CAD and PLM to many cross functional teams, and is currently working for Tata Technologies Business Development Team as a Siemens Application Engineer.
Tony Alfonsi